24v Motors Arrived!

Walking through my front door to find the motors had arrived I completely forgot how tired I was after walking up Snowdon. In my haste to hook things up and see what they could do, I bent the drive chain. Another one is on order, but in this video you can see I’m holding the motor in place with my hand and as the speed increases, the bent chain starts to cause significant wobble. I increased the speed as far as I dared but any faster and I think the motor might have ripped out of my hand or I might have suddenly had a chain hurtling towards my face. Anyway, here’s the vid. Can’t wait for the rest of the parts to arrive!!!

1st Sprocket Mounted

It works! Or at least it looks like it’s going to work.

The first sprocket arrived today and using a 3D printed template I drilled the holes to match the wheels and the sprocket is now sitting perfectly on the wheel.

Other sprockets are in the post so should be here by the end of the week. The sprockets for the most part are 55 tooth but I decided to go with larger 80 tooth sprockets on the two axles which are connected to the motors as this gives me a larger gear ratio (7:1) and would produce more torque. According to my calculations, this will give me a speed of 5kph without load. I haven’t yet estimated what speed it will do with load but it is surprisingly heavy and I still have the weight of the motors to add when they eventually arrive, sigh…

Gear Effeciencies

A lot’s been happening with the project lately so I’ve not had the time to write everything up but thinking back over the research I’ve been doing, I think it’s important to mention gear inefficiencies.

Up until recently I’d been favouring the idea of buying an off-the-shelf electric hub mounted motor:

I really like this idea because it’s simple; it would be easy to fabricate: just bolt the motor to the frame, attach the wheels and run two wires. Job done. Well almost…

The problem with this setup is that these types of motors are built for speed rather than torque, and that’s not what’s required for this wheelchair project. To reduce the speed of the motors and convert this to torque requires gears.

With this in mind, I had been thinking of a system whereby a chain runs between the motor and a large sprocket on the wheel hub. This would provide the necessary gears and you could easily change the size of the sprockets to fine-tune the speed/torque ratio:

Another advantage of this method is that because the motor isn’t embedded in the wheel, it’s less likely to get damaged. Considering that the motors will be one of the most expensive parts of the wheelchair, this is pretty important.

However, the main problem with this is that it’s adding more elements into the system, and the more elements you have, the more likely it is that something will go wrong. In this case, most likely it would be a weak link in the chain. There needs to be enough room between the motor and driven sprocket so that the motor can actually grip the chain, it’s bulky, and the chain would need constant lubrication and maintenance.

What’s more, the chain also reduces the efficiency of the system. The hub motor is 99% efficient as there are no gears. According to this article a chain and sprockets system is 80% efficient owing to “things such as friction, misalignment of pressure angles, lubrication, gear backlash and angular momentum”. We’d be losing 20% of the power by doing this! :O

In light of this, I think it possible to have the best of both worlds. Here the motor sits right against the hub sprocket and eliminates the chain.

According to societyofrobots.com this method, using two spur gears, is 90% efficient. Although there is still some loss, it’s better than 80%. There are other concerns too, such as having more fabrication to do, dirt/stones getting into the gears, if the axle bends then it might bend the sprocket or motor shaft, etc. However, it could be encased within a housing, would be easier to replace parts, is somewhat compact, and importantly it gives the opportunity to change gear ratios.

As this post is a few days late, I have since been thinking about hydraulic motors which could also be embedded in the hubs. Hydraulics might be the perfect solution but I have lots of research still to do.

This page was last updated on April 18th, 2018 by .
Permalink: Tag Archive: chain